程序代做CS代考 COMP90007 Internet Technologies Week 3 Workshop – cscodehelp代写
COMP90007 Internet Technologies Week 3 Workshop
Semester 2, 2021
Suggested solutions
© University of Melbourne 2021
1
Question 1 (Layers)
■ Identify 2 ways in which the OSI reference model and the TCP/IP reference model are the same.
■ Identify 2 ways in which these models differ. (NB: You can use the textbook to solve this question)
Similarities: Differences:
• stacking of layered protocols
• similar functionality in each of the layers
• layers above transport layer relate to applications
• TCP/IP does not distinguish between services, interfaces and protocols
• TCP/IP does not clearly separate physical and data link functions
2
Question 2 (Delay and
bandwidth)
■ Calculate the end-to-end transit time for a packet for
❑ ❑ ❑
•
• • •
GEO (Geostationary orbit) (altitude: 35,800 km), MEO (Medium Earth orbit) (altitude: 18,000 km) and LEO (Low Earth orbit) (altitude: 750 km) satellites.
Transit time = 2 × distance / speed of light, where c = 3.0×108 m/s
GEO: 239 ms MEO: 120 ms LEO:5ms
3
Question 3 (Delay and bandwidth)
■ An image is 1600 × 1200 pixels with 3 bytes/pixel.
Assume the image is uncompressed.
❑ How long does it take to transmit it over a 56-kbps modem channel, assuming zero propagation delay over the channel?
❑ Over a 1-Mbps cable modem? Over a 10-Mbps Ethernet?
❑ Over 100-Mbps Ethernet? Over gigabit Ethernet?
• Imagesize=1600×1200×3×8=46.08×106bits
• 56 kbps modem:
• 1 Mbps modem:
• 10 Mbps Ethernet:
• 100 Mbps Ethernet:
• 1 Gbps Ethernet:
823 s 46.1 s 4.61 s 0.46 s 0.046 s
4
Question 4 (Topology)
■ Consider the following 3 network topologies for connecting N nodes. In the general case of an N node network:
❑ (a) How many links are there in each network?
Linear: N − 1 links Ring: N links Full mesh: N(N − 1)/2 links
❑ (b) What is the maximum delay between any pair of nodes, assuming
each link has a delay of 10ms, and the shortest path is used between
nodes?
Linear: 10(N − 1) ms Ring: 10*N/2 ms Full mesh: 10 ms
❑ (c) What is the minimum number of links that need to be cut in order to
isolate one or more nodes?
Linear: 1 link Ring: 2 links Full mesh: N − 1 links
❑ (d) Which topology would you use to connect military command centres? Full mesh – cost not important, but reliability is essential
5
Question 5 (Topology)
■ Is an oil pipe a simplex system, a half-duplex system, a full duplex system or none of the above? Under which conditions?
• Oil can flow in either direction, but not both ways at once, therefore it cannot be full duplex.
• Depending on the situation, at an oil refinery, for example, an oil pipe is simplex, as the oil only flows in one direction.
• Theoretically oil can flow both ways, therefore it can be consider half duplex, similar to a single railroad track.
6
Question 6 (Topology)
■ List two solutions that one can use for sharing a link between multiple senders and explain these solutions briefly.
Ans: Time division multiplexing and frequency division multiplexing. There are others but these are the key ones we saw in class in detail. The explanations are available from slides 48,49,50 of Week 2 – Physical Layer.
7
